I bought my HP OMEN MAX 45L for the RTX 5090, but its Ryzen 7 9700X was still reserving 2 GiB for integrated graphics. HP’s stock BIOS didn’t expose an option to disable it. But using Smokeless UMAF to access the hidden AMD settings, I disabled the iGPU and increased usable RAM in Ubuntu by 2 GiB. Here’s how!
Disclaimer: This is an independent writeup and is not affiliated with or endorsed by HP. The below worked on my machine with F.10 firmware, but I can’t guarantee it will work on yours, or that it won’t brick your computer, cause data loss, or have unforeseen consequences. Proceed at your own risk and have a recovery method available. I provide no warranties and take no responsibility for damage or other consequences. Your mileage may vary!
My tested configuration:
- Computer: HP OMEN MAX 45L GT23-0xxx
- Motherboard: HP 8E55 / WukongOC
- Processor: AMD Ryzen 7 9700X
- Graphics: NVIDIA RTX 5090
- RAM: 64 GB DDR5
- BIOS: F.10, build date March 13, 2026
- Operating system: Ubuntu 26.04
1. Check Your Memory Beforehand
In Ubuntu, you can check your current memory total like so:
free -h
grep '^MemTotal:' /proc/meminfo
And the integrated GPU’s memory reservation:
sudo dmesg | grep -i 'amdgpu.*VRAM'
One of the resulting lines for me showed:
amdgpu 0000:09:00.0: [drm] Detected VRAM RAM=2048M, BAR=2048M
My BIOS had reserved 2 GiB of system RAM for the iGPU, even though my display was connected to the NVIDIA card, and the motherboard didn’t even have a GPU port on it!
2. Prepare a Smokeless UMAF USB Drive
Download UniversalAMDFormBrowser.zip from the Smokeless UMAF repository. Read the project’s warnings before proceeding.
Back up anything important on your USB drive. Use a FAT32-formatted drive and extract the ZIP’s contents directly into its root. It should look like this:
DisplayEngine.efi
SetupBrowser.efi
UiApp.efi
EFI/
Boot/
Bootx64.efi
Make sure these files aren’t inside an extra enclosing folder. UMAF exposes AMD’s hidden configuration menus; this process doesn’t require flashing a modified BIOS or manually editing variable offsets.
3. Disable Secure Boot and Boot the USB
Restart the OMEN and press F10 to enter HP’s normal BIOS setup. Temporarily disable Secure Boot, preserving its existing keys and keeping UEFI boot enabled. Save and restart.
If you use Windows with BitLocker or Device Encryption, have your recovery key available and follow Microsoft’s guidance for suspending protection before firmware changes. Changes to the boot environment can trigger recovery.
With the USB connected, press F9 during startup and select its UEFI boot entry. This should launch UMAF.
Have your monitor connected to the dedicated graphics card. The next step disables the processor’s integrated graphics and any display outputs driven by it.
4. Enable dGPU Only Mode, and Press F10 to Save
In UMAF, navigate to:
Device Manager > AMD CBS > NBIO Common Options > GFX Configuration
Change dGPU Only Mode from Auto to Enabled. Its help text says “Disable iGPU if dGPU is detected.” Leave the other settings alone.
Then press F10 in UMAF to save and exit, confirming the save when prompted.
This was the main gotcha for me: I couldn’t find a working save-and-exit option in the menus. F10 was what saved the change. Simply changing the displayed value wasn’t enough.
If your menus or available settings differ, stop and investigate rather than guessing.
5. Reboot and Verify
Boot Ubuntu again and run:
free -h
grep '^MemTotal:' /proc/meminfo
lspci -nn | grep -Ei 'VGA|3D|Display'
My usable memory increased from 59.4 GiB to 61.4 GiB. The precise total afterward was:
MemTotal: 64364324 kB
The integrated Radeon GPU disappeared from the PCI device list, while the RTX 5090 remained present and working. Reading back the firmware setting also confirmed that dGPU Only Mode = Enabled had persisted.
That recovered approximately 2 GiB of system RAM. It doesn’t increase the NVIDIA card’s VRAM.
After finishing with the USB, you can re-enable Secure Boot. To undo the graphics change, boot UMAF again, return dGPU Only Mode to its original Auto value, and press F10 to save.
If this works on another OMEN configuration, leave a comment with your model, CPU, BIOS version, and before-and-after memory totals!